|
TIPC 50 |
TIPC 50ST |
TIPC 85 |
TIPC 85ST |
TIPC 90 |
DESCRIPTION |
Flexible corrosive water and oil mixture |
Flexible corrosive water and oil mixture for use in high wear applications |
High performance enhanced flexibility |
High performance enhanced flexibility for use in high wear applications |
High performance, corrosive resistant coating |
TYPE |
Powder Epoxy |
Powder Epoxy |
Powder-Modified Novolac |
Powder-Modified Novolac |
Powder-Phenolic Novolac |
TEMPERATURE |
To 250°F (121°C) |
To 250°F (121°C) |
To 300°F (149°C) |
To 300°F (149°C) |
To 400°F (204°C) |
APPLIED THICKNESS |
10-20 MILS |
10-20 MILS |
10-20 MILS |
10-20 MILS |
8-20 MILS |
PRESSURE |
UP TO YIELD STRENGTH OF PIPE |
UP TO YIELD STRENGTH OF PIPE |
UP TO YIELD STRENGTH OF PIPE |
UP TO YIELD STRENGTH OF PIPE |
UP TO YIELD STRENGTH OF PIPE |
PRIMARY SERVICE |
Saltwater disposal/injection Wells, low temperature and pressure, sweet oil and gas production |
Saltwater disposal/injection Wells, low temperature and pressure, sweet oil and gas production |
Oil, natural gas, fresh and salt water, CO2, mild H2S and alkaline service to pH 12 for corrosion with paraffin mitigation |
Oil, natural gas, fresh and salt water, CO2, mild H2S and alkaline service to pH 12 for corrosion with paraffin mitigation |
Oil, natural gas, fresh and salt water, CO2, mild H2S and alkaline service to pH 12 for corrosion with paraffin mitigation |
PRIMARY APPLICATION |
New and used tubular goods and line pipe, flow lines hydraulic improvement |
Enhanced for increased wear resistance. New and used tubular goods and line pipe, flow lines hydraulic improvement |
Drill pipe and production tubing, water and CO2 injection, disposal wells and flow lines, hydraulic improvement |
Enhanced for increased wear resistance. Drill pipe and production tubing, water and CO2 injection, disposal wells and flow lines, hydraulic improvement |
Drill pipe and production tubing, down hole equipment, hydraulic improvement |
COMMENTS |
Hydraulic Improvement: All coatings provide a smooth and consistent surface allowing for improved flow dynamics, maximizing productivity. |
NOTES |
Complete flushing of stimulation fluids should cause minimal effect to the coating. TIPC recommends appropriate care, handling, and installation on all internally coated material. |
PLANT CAPABILITIES: 2-3/8" to 12-3/4" O.D. |
TIPC 50 |
DESCRIPTION |
Flexible corrosive water and oil mixture |
TYPE |
Powder Epoxy |
TEMPERATURE |
To 250°F (121°C) |
APPLIED THICKNESS |
10-20 MILS |
PRESSURE |
UP TO YIELD STRENGTH OF PIPE |
PRIMARY SERVICE |
Saltwater disposal/injection Wells, low temperature and pressure, sweet oil and gas production |
PRIMARY APPLICATION |
New and used tubular goods and line pipe, flow lines hydraulic improvement |
COMMENTS |
Hydraulic Improvement: All coatings provide a smooth and consistent surface allowing for improved flow dynamics, maximizing productivity. |
NOTES |
Complete flushing of stimulation fluids should cause minimal effect to the coating. TIPC recommends appropriate care, handling, and installation on all internally coated material.Flexible corrosive water and oil mixture |
PLANT CAPABILITIES: 2-3/8" to 12-3/4" O.D. |
TIPC 50ST |
DESCRIPTION |
Flexible corrosive water and oil mixture for use in high wear applications |
TYPE |
Powder Epoxy |
TEMPERATURE |
To 250°F (121°C) |
APPLIED THICKNESS |
10-20 MILS |
PRESSURE |
UP TO YIELD STRENGTH OF PIPE |
PRIMARY SERVICE |
Saltwater disposal/injection Wells, low temperature and pressure, sweet oil and gas production |
PRIMARY APPLICATION |
Enhanced for increased wear resistance. New and used tubular goods and line pipe, flow lines hydraulic improvement |
COMMENTS |
Hydraulic Improvement: All coatings provide a smooth and consistent surface allowing for improved flow dynamics, maximizing productivity. |
NOTES |
Complete flushing of stimulation fluids should cause minimal effect to the coating. TIPC recommends appropriate care, handling, and installation on all internally coated material.Flexible corrosive water and oil mixture |
PLANT CAPABILITIES: 2-3/8" to 12-3/4" O.D. |
TIPC 85 |
DESCRIPTION |
High performance enhanced flexibility |
TYPE |
Powder-Modified Novolac |
TEMPERATURE |
To 300°F (149°C) |
APPLIED THICKNESS |
10-20 MILS |
PRESSURE |
UP TO YIELD STRENGTH OF PIPE |
PRIMARY SERVICE |
Oil, natural gas, fresh and salt water, CO2, mild H2S and alkaline service to pH 12 for corrosion with paraffin mitigation |
PRIMARY APPLICATION |
Enhanced for increased wear resistance. New and used tubular goods and line pipe, flow lines hydraulic improvement |
COMMENTS |
Drill pipe and production tubing, water and CO2 injection, disposal wells and flow lines, hydraulic improvement |
NOTES |
Complete flushing of stimulation fluids should cause minimal effect to the coating. TIPC recommends appropriate care, handling, and installation on all internally coated material.Flexible corrosive water and oil mixture |
PLANT CAPABILITIES: 2-3/8" to 12-3/4" O.D. |
TIPC 85ST |
DESCRIPTION |
High performance enhanced flexibility for use in high wear applications |
TYPE |
Powder-Modified Novolac |
TEMPERATURE |
To 300°F (149°C) |
APPLIED THICKNESS |
10-20 MILS |
PRESSURE |
UP TO YIELD STRENGTH OF PIPE |
PRIMARY SERVICE |
Oil, natural gas, fresh and salt water, CO2, mild H2S and alkaline service to pH 12 for corrosion with paraffin mitigation |
PRIMARY APPLICATION |
Enhanced for increased wear resistance. Drill pipe and production tubing, water and CO2 injection, disposal wells and flow lines, hydraulic improvement |
COMMENTS |
Drill pipe and production tubing, water and CO2 injection, disposal wells and flow lines, hydraulic improvement |
NOTES |
Complete flushing of stimulation fluids should cause minimal effect to the coating. TIPC recommends appropriate care, handling, and installation on all internally coated material.Flexible corrosive water and oil mixture |
PLANT CAPABILITIES: 2-3/8" to 12-3/4" O.D. |
TIPC 90 |
DESCRIPTION |
High performance, corrosive resistant coating |
TYPE |
Powder-Modified Novolac |
TEMPERATURE |
To 400°F (204°C) |
APPLIED THICKNESS |
8-20 MILS |
PRESSURE |
UP TO YIELD STRENGTH OF PIPE |
PRIMARY SERVICE |
Oil, natural gas, fresh and salt water, CO2, mild H2S and alkaline service to pH 12 for corrosion with paraffin mitigation |
PRIMARY APPLICATION |
Drill pipe and production tubing, down hole equipment, hydraulic improvement |
COMMENTS |
Drill pipe and production tubing, water and CO2 injection, disposal wells and flow lines, hydraulic improvement |
NOTES |
Complete flushing of stimulation fluids should cause minimal effect to the coating. TIPC recommends appropriate care, handling, and installation on all internally coated material.Flexible corrosive water and oil mixture |
PLANT CAPABILITIES: 2-3/8" to 12-3/4" O.D. |